Renewable Energy

Emulsion buffer layer curbs screen-printing degradation in copper-plated HJT solar cells

Chinese researchers link efficiency losses to wear of screen mesh knuckles and find that a 4.7% emulsion coverage ratio best protects passivation during full-area photoresist printing.

Marisol QuinteroNovember 15, 20265 min read0 views
Conceptual close-up of a screen-printing mesh held slightly above a silicon wafer by a thin emulsion buffer layer, depicting the screen redesign studied to reduce mechanical damage during photoresist printing.

Screen printing is a standard step in solar cell metallization, but the process itself can degrade device performance, and the risk is especially acute for copper-plated silicon heterojunction (HJT) cells that are being pursued as a route to lower metallization costs and reduced silver consumption.

The mechanical pressure and thermal treatments applied during printing can damage the sensitive passivating contact structures of HJT cells, raising recombination losses and pulling down conversion efficiency. A group of researchers in China has now examined how that damage arises in copper-plated HJT devices and proposed a modification to the screen itself to limit it, work they say could ease the technology's path to large-scale manufacturing.

Why photoresist printing differs

Corresponding author Lang Zhou explained that applying photoresist by screen printing in HJT production is fundamentally different from printing silver paste. In silver paste printing, screen openings cover only 2–5% of the total area, and an emulsion layer shields the rest of the surface so the mesh never touches the wafer directly. Full-area photoresist coating, by contrast, typically uses a screen with no emulsion coverage so that resist is deposited uniformly across the whole wafer — which means the mesh comes into direct and extensive contact with the wafer on every printing cycle.

Measured losses

Earlier work cited by the team recorded conversion efficiency falling from 26.2% to 25.7% across 15,000 consecutive printing cycles in commercial production. The losses came mainly from open-circuit voltage and fill factor, while short-circuit current density and electrical resistance stayed largely unchanged. Minority carrier lifetime degradation rose from 0.61% with a new screen to 11.0% after 15,000 cycles.

Using three-dimensional confocal microscopy, the scientists traced the problem to progressive wear of the screen mesh knuckles. As the knuckles flatten, their contact area with the wafer grows, increasing mechanical stress on the passivation layers beneath. Scanning electron microscopy showed no visible surface scratches, but photoluminescence measurements confirmed higher recombination losses, pointing to damage at the amorphous silicon/crystalline silicon interface.

An emulsion buffer layer

To break the direct contact, the researchers added an emulsion buffer layer to the screen and tested six patterns with emulsion coverage ratios between 2.9% and 16.6%. The results showed a trade-off: greater coverage protected the wafer better but disturbed photoresist distribution. A coverage ratio of 4.7% gave the best balance, holding minority carrier lifetime degradation to 0.41% after 10,000 cycles while keeping coating uniformity reasonably good.

The team attributes the improvement to the emulsion layer keeping mesh and wafer apart, reducing cumulative mechanical damage to the sensitive passivation stack.

"The findings demonstrate that a relatively simple modification to screen design can substantially mitigate printing-induced degradation," Zhou said, describing it as a practical approach to improving the manufacturing reliability of copper-plated HJT cells.

The results appear in "Screen-printing photoresist induced efficiency degradation and mitigation in Cu-plated SHJ solar cells," published in Solar Energy.

The work lands amid widening interest in copper metallization as a substitute for silver contacts in HJT devices. In April 2026, researchers at China's Nankai University reported a silver-free HJT cell at 25.2% efficiency, using plasma-induced interface engineering and copper electroplating to address adhesion, contact resistance and stability challenges at the ITO interface. Separately, scientists at Germany's Forschungszentrum Jülich reached 23.08% with a fully copper-metallized HJT cell — a relatively small penalty compared with its silver-metallized counterpart — while a design combining silver-copper paste on the front with silver contacts on the rear reached 23.95%. Those results underline copper's potential to cut silver use, although further improvements in processing and electrical performance remain necessary.